Victron Phoenix Smart IP43 Charger 24V/25A (2 bank) 120-240VAC Requires 5-15P Mains Cord
Phoenix Smart IP43 Charger 24/25 (1+1) 120-240VAC Requires 5-15P Mains Cord
With boat owners in mind, this adaptive 5-step charger can provide either 30A or
50A of charge to each of the three battery banks. Or the Phoenix 1+1 model
provides 3A to the starter battery, the rest to the ‘house’ bank. 24V models are
available with a 16A/25A charge. Bluetooth enabled, you can monitor the charger
and set alarms straight from your phone.
Bluetooth Smart built-in: The wireless solution to set up, monitor, update and
synchronize Phoenix Smart IP43 Chargers.
Phoenix Smart (1+1): two outputs to charge 2 battery banks: The second output,
limited to approximately 4A and with a slightly lower output voltage, is
intended to top up a starter battery.
Phoenix Smart (3): three full current outputs to charge 3 battery banks: Each
output can supply the full rated output current. But the total of the 3
outputs combined can never exceed the current rating of the charger.
Automatic voltage compensation: The charger compensates for voltage drop over
the DC cabling by slightly increasing output voltage when the DC current
Adaptive 6-stage charge algorithm: bulk– absorption – recondition – float –
storage – refresh: The Phoenix Smart Charger features our well-known
‘adaptive’ battery management system that can be preset to suit different
types of batteries. The ‘adaptive’ feature will automatically optimize the
charging process relative to the way the battery is being used.
The right amount of charge: variable absorption time: When only shallow
discharges occur (a yacht connected to shore power for example) the absorption
time is kept short in order to prevent overcharging of the battery. After a
deep discharge, the absorption time is automatically increased to make sure
that the battery will be fully charged.
Preventing damage due to excessive gassing: the BatterySafe mode: If in order
to quickly charge a battery, a high charge current in combination with a high
absorption voltage has been chosen, the charger will prevent damage due to
excessive gassing by automatically limiting the rate of voltage increase once
the gassing voltage has been reached.
Less maintenance and aging when the battery is not in use: the Storage Mode:
The Storage Mode kicks in whenever the battery has not been subjected to
discharge for 24 hours. In the Storage Mode, float voltage is reduced to 2,2
V/cell (13,2 V for a 12 V battery) to minimize gassing and corrosion of the
positive plates. Once a week the voltage is raised back to the absorption
level to ‘equalize’ the battery. This feature prevents stratification of the
electrolyte and sulphation, a major cause of early battery failure.
Also charges Li-ion (LiFePO4) batteries: Charger on-off control can be
implemented by connecting a relay or open collector optocoupler output from a
Li-ion BMS to the remote on-off port. Alternatively, full control of voltage
and current can be achieved with Bluetooth.
Fully programmable charge algorithm: The charge algorithm can be programmed
with help of Bluetooth or the VE.Direct interface. Three preprogrammed
algorithms can be selected with the mode button.
Optional external battery voltage and temperature sensing via Bluetooth: A
Smart Battery Sense or a BMV-712 Smart Battery Monitor can be used to
communicate battery voltage and temperature to one or more Phoenix Smart IP43
Remote on-off: The remote on/off consists of two terminals: Remote H and
Remote L. A remote on/off switch or relay contact can be connected between H
and L. Alternatively, terminal H can be pulled high, or terminal L can be
VE.Direct interface: For a wired data connection to a Color Control panel, PC,
or other devices.
Programmable relay: Can be programmed using the VE.Direct interface or a
Bluetooth-enabled device to trip on an alarm or other events.
Synchronized charging: Pairing two or more Phoenix Smart IP43 Chargers in a
VE.Smart Network, enables synchronized charging. This improves the charge
efficiency and battery life.